Bite alarm sets include:
3 * wireless multi-LED bite alarm
1* wireless touch receiver
1* plastic box
INDICATOR
Replacing the battery: unscrew locking nut, remove the cover on the back of the indicator, and insert R9/6LR61 9V battery (not included) observing the correct polarity (+/-) and then close the cover.
Mount the alarm on a buzzer bar or bank stick.
Press and hold Volume button (V) few seconds. Beep and flashing lights confirms, that bite indicator is ready to work.
Thread the fishing line over the roller sensor (A). A bite is indicated by sound and flashing lights allowing you to identify the bite indicator, which has been activated. Beep tone depends on bite direction (forward/reversal).
Press the right button you can adjust volume (V), sensitivity (S), tone (T) and LED color (W) – there are seven colors available. Press and hold on few seconds (W) button to ON/OFF night mode – roller sensor light.
To switch indicator OFF press and hold volume control (V) button, LED is then flashing.
The maximum distance of transmission to the wireless transmitter is between 100 – 150 meters depending on conditions.
RECEIVER
Replacing the battery: remove the cover on the back of the receiver, and insert 3 AAA/R03 1,5V battery (not included) observing the correct polarity (+/-) and then close the cover.
To switch power ON pull down switch (1). Vibes, all 5 LED flashing in sequence and lighting display confirm that receiver is ready to work.
Bite is indicated by sound alarm and flashing LED color according to activated indicator and showing info on receiver display.
Replacing the battery: remove the cover on the back of the receiver, and insert 3 AAA/R03 1,5V battery (not included) observing the correct polarity (+/-) and then close the cover.
To switch power ON pull down switch (1). Vibes, all 5 LED flashing in sequence and lighting display confirm that receiver is ready to work.
Bite is indicated by sound alarm and flashing LED color according to activated indicator and showing info on receiver display.
Receiver setup – touch panel:
1a – Volume control
2a – Tone control
3a – Vibes ON/OFF
4a – select to view which indicator info is actually shown on LCD.
2a – Tone control
3a – Vibes ON/OFF
4a – select to view which indicator info is actually shown on LCD.
Display icons:
1b – Range of indicators
2b – Indicators battery level
3b – Bite direction (Forward/Reversal)
4b – Number of bites on each indicator
2b – Indicators battery level
3b – Bite direction (Forward/Reversal)
4b – Number of bites on each indicator
1c – Receiver battery level
2c – Receiver volume level
3c – Receiver tone level
4c – Vibes ON/OFF
To switch power ON pull the button (1) down. To switch power OFF – pull it up.
Press button (2) to switch ON/OFF display and touch panel.
RECEIVER SETUP
Receiver could be connected with up to 5 indicators at the same time.
How to setup receiver:
1. Press memory button (2) and hold about three seconds until two signals sounds.
2. Press button(4a), to adjust color of pre-set LED according to indicator.
3. To confirm correct one press memory button (2).
4. Move encoding indicator’s roller to activate.
5. Two sounds confirm encoding finish successfully.
6. After encoding please check equipment connections working appropriate.
To reset all indicator connections with receiver press and hold memory button (2) about ten seconds. All setup will be cancelled.
How to setup receiver:
1. Press memory button (2) and hold about three seconds until two signals sounds.
2. Press button(4a), to adjust color of pre-set LED according to indicator.
3. To confirm correct one press memory button (2).
4. Move encoding indicator’s roller to activate.
5. Two sounds confirm encoding finish successfully.
6. After encoding please check equipment connections working appropriate.
To reset all indicator connections with receiver press and hold memory button (2) about ten seconds. All setup will be cancelled.
PACKing :30CM*26CM*13CM
Weight:1KGS
No comments:
Post a Comment